型号: PXI-6133

产品编号: 779129-01

NI 6132/6133 Specifications

This document lists the I/O terminal summary and specifications for the NI 6132/6133.

For the most current edition of this document, refer to ni.com/manuals. Refer to the DAQ Getting Started Guide for more information about accessing documents on the NI-DAQ CD.

    Note  With NI-DAQmx, National Instruments has revised its terminal names so they are easier to understand and more consistent among NI hardware and software products. The revised terminal names used in this document are usually similar to the names they replace. For a complete list of Traditional NI-DAQ terminal names and their NI-DAQmx equivalents, refer to the Terminal Name Equivalents table in the S Series Help.

Table 1.  I/O Terminal Summary

Table 1.  I/O Terminal Summary (Continued)

Specifications

The following specifications are typical at 25 °C unless otherwise noted.

Analog Input

Input Characteristics

Number of channels

NI 6132 .......................................4

NI 6133 .......................................8

Type of ADC

Resolution...................................14 bits, 1 in 16,384 Pipeline .......................................0

Sampling rate

Maximum....................................2.5 MS/s per channel Minimum ....................................No minimum

Input impedance

AI – to AI GND ..........................100 MΩ in parallel with 10 pF

AI + to AI GND..........................100 MΩ in parallel with

10 pF

Input bias current.............................±2 pA typ, ±25 pA max Input offset current..........................±1 pA typ, ±10 pA max

Input coupling..................................DC

Max working voltage for all analog input channels

Positive input (AI +)................... ±11 V for all ranges,

Measurement Category I

Negative input (AI –) ................. ±11 V for all ranges,

Measurement Category I

  Caution Do not use for measurements within Categories II, III, and IV.

Overvoltage protection (AI +, AI –)..................................... ±36 V

Input current during

overvoltage conditions.................... ±20 mA max

Input FIFO size

NI 6132....................................... 16 MS

NI 6133....................................... 16 or 32 MS

Data transfers.................................. DMA, interrupts,

programmed I/O

DMA mode ..................................... Scatter-gather

DC Transfer Characteristics

INL.................................................. ±0.6 LSB typ,

±1 LSB max

DNL ................................................±0.25 typ, ±0.75 max, no missing codes

Dynamic Characteristics

Phase mismatch...............................±2° at 1 MHz

Table 2.  NI 6132/6133 Analog Input Dynamic Characteristics

Typical Performance Graphs

Stability

Recommended warm-up time .........15 min

Calibration

Level................................................5.000 V (±2.5 mV)

(actual value stored in

EEPROM)

Temperature coefficient ..................±5.0 ppm/°C max

Long-term stability..........................±15 ppm/ 1,000 h

Digital I/O

Number of channels.........................8 input/output

Compatibility...................................TTL/CMOS

Table 3.  Digital Logic Levels

Power-on state.................................Input (high-impedance)

Data transfers...................................DMA, interrupts,

programmed I/O

Input buffer......................................2,044 bytes

Output buffer...................................2,044 bytes

Transfer rate (1 word = 8 bits).........10 Mwords/s

Timing I/O

Number of channels.........................2 up/down counter/timers, 1 frequency scaler

Resolution

Counter/timers ............................24 bits Frequency scaler .........................4 bits

Compatibility...................................TTL/CMOS

Base clocks available

Counter/timers ............................20 MHz, 100 kHz

Frequency scaler .........................10 MHz, 100 kHz

Base clock accuracy ........................±0.01%

Max source frequency .....................20 MHz

Min source pulse duration............... 10 ns, edge-detect mode

Min gate pulse duration .................. 10 ns, edge-detect mode

Data transfers.................................. DMA, interrupts,

programmed I/O

DMA modes.................................... Scatter-gather

Triggers

Analog Trigger

Source ............................................. All analog input channels

Level ............................................... ± full-scale

Slope ............................................... Positive or negative

(software-selectable)

Resolution....................................... 8 bits, 1 in 256

Hysteresis........................................ Programmable

Bandwidth (–3 dB).......................... 5 MHz internal/external

Digital Trigger

Compatibility .................................. TTL

Response......................................... Rising or falling edge

Pulse width...................................... 10 ns min

RTSI Trigger Lines (PCI Only)

Trigger lines <0..6> ........................ 7 RTSI clock...................................... 1

PXI Trigger Bus (PXI Only)

Trigger lines <0..6> ........................ 7 Star trigger ...................................... 1

Bus Interface

Type ................................................Master, slave

Power Requirement

+5 VDC (±5%)

NI 6132....................................... 2.2 A

NI 6133....................................... 3.0 A

+3.3 V

NI 6132....................................... 1.0 A

NI 6133....................................... 1.2 A

–12 VDC

NI 6132....................................... 45 mA

NI 6133....................................... 70 mA

Power available at I/O connector.... +4.65 to +5.25 VDC

at 1 A

Physical

Dimensions (not including connectors)

NI PCI-6132/6133......................31.2 cm × 10.6 cm (12.3 in. × 4.2 in.)

NI PXI-6132/6133......................16.0 cm × 10.0 cm

(6.3 in. × 3.9 in.)

I/O connector ..................................68-pin male SCSI-II type

Environmental

Operating temperature ....................0 to 50 °C

Storage temperature........................–20 to 70 °C

Humidity.........................................10 to 90% RH,

noncondensing

Maximum altitude...........................2,000 m

Pollution Degree .............................2 Indoor use only.

Safety

The NI 6132/6133 devices are designed to meet the requirements of the following standards of safety for electrical equipment for measurement, control, and laboratory use:

•         IEC 61010-1, EN 61010-1

•         UL 61010-1, CAN/CSA-C22.2 No. 61010-1

    Note  For UL and other safety certifications, refer to the product label, or visit ni.com/ certification, search by model number or product line, and click the appropriate link in the Certification column.

Electromagnetic Compatibility

The NI 6132/6133 devices are designed to meet the requirements of the following standards of EMC for electrical equipment for measurement, control, and laboratory use:

•         EN 61326 EMC requirements; Minimum Immunity

•         EN 55011 Emissions; Group 1, Class A

•         CE, C-Tick, ICES, and FCC Part 15 Emissions; Class A

    Note      For EMC compliance, operate this device according to product documentation.

CE Compliance

This product meets the essential requirements of applicable European Directives, as amended for CE marking, as follows:

•         73/23/EEC; Low-Voltage Directive (safety)

•         89/336/EEC; Electromagnetic Compatibility

Directive (EMC)

    Note      Refer to the Declaration of Conformity (DoC) for this product for any additional regulatory compliance information. To obtain the DoC for this product, visit ni.com/certification, search by model number or product line, and click the appropriate link in the Certification column.

Waste Electrical and Electronic Equipment (WEEE)

   EU Customers        At the end of their life cycle, all products must be sent to a WEEE recycling center. For more information about WEEE recycling centers and National Instruments WEEE initiatives, visit ni.com/environment/weee.htm.

National Instruments, NI, ni.com, and LabVIEW are trademarks of National Instruments Corporation.

Refer to the Terms of Use section on ni.com/legal for more information about National Instruments trademarks. Other product and company names mentioned herein are trademarks or trade names of their respective companies. For patents covering National Instruments products, refer to the appropriate location: Help»Patents in your software, the patents.txt file on your CD, or ni.com/patents.

© 2004–2006 National Instruments Corporation. All rights reserved.                                                 371231D-01                 Jul06